Samsung SWL-3000AP Podręcznik Użytkownika

SWL-3000AP Series Access Point User’s Guide * This User’s Guide can be used on SWL-3000AP, 3000AP(DA), 3300AP and 3300AP(DA).

6④ TCP/IP address environment is set on [Basic] Dialogue Box. ♦ Specify an IP address After consulting with your system administrator, you ente

7♦ Set Channel for AP use. Channel index should be between 1 and 14(differs from country to country). Notice : If you are operating two or more Acc

8⑧ When you click [Confirm & Apply] button to apply new configuration, “Configuration Summary” window, which shows new configuration, will appear

9⑪ After you enter the password, click [OK] button. ⑫ If you want to set default values, click [Load Default values] button. Then, AP Configuratio

104. PTP Setting Using AP Manager ① PTP stands for Point to Point, and it is used to connect two divided networks into one using AP as Wireless Bri

11③ When Operation Mode of AP is selected for “Point-to-Point” on [Radio] Dialogue Box, [Remote ID (PTP)] Box will appear to enter MAC ID of Wireles

12 ⑤ ESSID and Channel of two APs must be identical in PTP mode ⑥ When you click [Confirm & Apply] button to apply new configuration

13 ⑦ If new settings are entered correctly, click [Apply] button to apply new configuration. ⑧ When you click [Apply] button, “Password” window

14new configuration. ⑪ After rebooting, choose selected proper AP on “List Box”. Then, the selected AP set with PTP Mode can be confirmed on [Selec

15 5. AML Setting Using AP Manager ① AML stands for Automatic Multi-link. Using AP as Wireless Bridge, it is used to connect several divided networ

Notice when you establish * We recommend you to avoid this places where may be cause of performance decline or trouble. 1. Places with high humidity

16 ④ Select either “Master” or “Slave” for [Control Mode] on [Automatic Multi-link] Box. Basically, AML Mode consists of two or more APs, and set on

17 ⑤ All of ESSID and Channel of AP set in AML mode must be identical. ⑥ When you click [Confirm & Apply] button to apply new configuration

18 ⑨ After you enter the password, click [OK] button. ⑩ When you click [Apply] button instead of [Confirm & Apply] button, “Password” window

196. Bridge Table and Protocol Management Using AP Manager ① Using AP Manager, list of Wired and Wireless Station(PC or AP) connected to current AP

20④ [Age Time] on [Bridge Table] Management Box shows cycle of AP refreshing “Bridge Table”. The use of Default Values is recommended. ⑤ After sel

21 ⑩ If new settings are entered correctly, click [Apply] button to apply new configuration. ⑪ When you click [Apply] button, “Password” window w

227. NAT Setting Using AP Manager ① NAT stands for Network Address Translation, and it is used to establish private network domain. Using NAT, any

23③ When you click [Confirm & Apply] button to apply new configuration, “Configuration Summary” window, which shows new configuration, will appe

24⑦ When you click [Apply] button instead of [Confirm & Apply] button, “Password” window will appear immediately skipping “Configuration Summary

25 Select “TCP/IP” [Properties]of LAN Adapter to use on [Configuration] Menu. Set “IP Address” and “Subnet Mask” on [IP Address] Menu.In this case,

1. Introduction⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅ 1 2. Installation⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅⋅

26 Configuration has been completed for desktop or notebook PC to connect with AP. In this case, the specified IP Address of desktop or notebook PC

278. DHCP Server Setting Using AP Manager ① DHCP stands for Dynamic Host Configuration Protocol, it is protocol that enables Network administrator

28 Notice : When you select DHCP Server, the values on the window show information assigned to DHCP Client with IP Address. In most cases, values of

29⑤ To set the scope of assignable IP Address, first check on [Empty] check box on the left. Then, “Empty” will be changed to “Valid”, and you can s

30 ⑪ After you enter the password, click [OK] button. ⑫ When you click [Apply] button instead of [Confirm & Apply] button, “Password” window

31 Notice : If you want to set DHCP Client instead of DHCP Server, select [Basic] on “Tab Bar” menu of AP. Then, select “Obtain an IP address automat

329. NAT and DHCP Server Simultaneous Setting Using AP Manager ① After executing AP Manager, select [Server] tab on “Tab Bar” to set DHCP Server an

33③ When you click [Confirm & Apply] button to apply new configuration, “Configuration Summary” window, which shows new configuration, will appe

34⑦ When you click [Apply] button instead of [Confirm & Apply] button, “Password” window will appear immediately skipping “Configuration Summary

3510. ADSL and Cable Modem Connection Setting Using AP Manager ① After executing AP Manager, click [Advanced] and [Internet Connection] on “Menu Ba

Also, this equipment is available for home use. This device complies with part 15 of the FCC Rules. Operation is subject to the following two c

36Notice: ADSL can generally be divided into two service types supporting PPPoE or PPTP, but PPPoE is more common. If you don’t know your ADSL servi

37③ Set NAT and DHCP Server referring Chapter 9. ④ Click [Finish] button to complete setting. DHCP Server andNAT Setting

38⑤ A window will appear and ask you to apply new settings immediately. If you do not want to apply new settings, select [No(N)]. ⑥ If you click

3910.2 Settings for ADSL – PPTP ① When the above page appears, enter the user name given by your ISP(Internet Service Provider) in the “User Name

40④ Set NAT and DHCP Server referring Chapter 9. ⑤ Click [Finish] button to complete setting. Setting DHCP Server and NAT

41⑥ A window will appear and ask you to apply new settings immediately. If you do not want to apply new settings, select [No(N)]. ⑦ If you click

4210.3 Settings for Cable Modem ① Set NAT and DHCP Server referring Chapter 9. Notice : Personal Information Setting is not needed because Cable m

43③ A window will appear and ask you to apply new settings immediately. If you do not want to apply new settings, select [No(N)]. ④ If you click

4411. Encryption Setting Using AP Manager ① After executing AP Manager, select [Security] tab on “Tab Bar” to set encryption. Then, select “Encrypti

45④ Enter the agreed password phrase to set encryption in “Passphrase,” and click [Generate] button to create WEP Key. After generating the keys,

11. Introduction Thank you for purchasing SAMSUNG SWL-3000AP Series Access Point(AP). This guide describes the installation and basic configuratio

46 ⑥ If new settings are entered correctly, click [Apply] button to apply new configuration. ⑦ When “Password” window appear, enter the password. T

4712. User Access Control Setting Using AP Manager ① “User Access Control” is function that shows permission of using AP to MAC ID Table of Wireles

48 Click [+] icon, and enter MAC ID as shown on the window below. Then, click [OK] button to add MAC ID on [Allowed Table]. Select Connection

49⑥ When you want to deny specific MAC ID and permit the other, select “pass” on [Other Stations] Box. Then, add the MAC ID on [Denied Table], which

50⑨ If you want to export and save MAC IDs registered either on [Allowed Table] or [Denied Table], click [Export] button. Then, it will be saved whe

51 ⑩ You can combine and use various settings as you wish. ⑪ If new settings are entered correctly, click [Apply] button to apply new configura

5213. Firmware Upgrade Using AP Manager ① Whenever the new version of AP Firmware is available, you can upgrade AP firmware into higher version usi

53⑤ Downloaded the latest version of AP firmware in local disk of your PC Notice: AP firmware corresponding to your AP can be downloaded in Magi

54⑧ Click the [Load] button after the file is selected. Then, “Password” window will be displayed. ⑨ Enter the password, default password is “pu

5514. Data Transmission Status Check Using AP Manager ① Data transmission traffic status of current AP can be confirmed using AP Manager. ② When

2 ! The Front and Rear View of SWL-3300AP ! The Front and Rear View of SWL-3300AP(DA) DC in RS-232CRJ-45 Connecto

56⑤ If you want to confirm with line graph, select “Line” instead of “Histogram” on Related Information Confirm Box. ⑥ In this case, if confir

57# SNMP : Simple Network Management Protocol # MIB : Management Information Base ⑨ Confirming Traffic information you want enables more effic

5815. AP Setting Using Web Browser ① Open Web Browser. (Beyond IE 4.0 or Netscape 4.0) ② Enter AP’s IP Address on “Address” of the Web Browser. P

59 ④ Internet Connection Setting page”(default page) appears. ⑤ Simple Configuration Mode is for Setting of Internet Connection Environment, and

6016. AP Setting Using TELNET ① Open “Run” on [Start] menu of desktop and notebook PC. Enter the IP Address for Internet Connection as following Ex

6117. HyperTerminal Setting for RS-232C(COM Port) Communication ① Execute the HyperTerminal under MS-Windows 95/98/Me/2000/NT/XP operating system by

62③ As displayed above, type “AP MANAGER” in the name field, and click [OK] button. You can enter any name you wish for the connection. ④ Select t

63⑥ If all the steps above are executed correctly, then the following menu will be displayed on the HyperTerminal window. The default password is “p

6418. AP Basic Setting Using RS-232C(COM Port) ① Choose [Basic] menu on [ROOT] menu. ② Select the following order to set Wireless LAN ESSID.

65③ Select the following order to change Wireless Channel. Enter the proper channel number after the phrase “Enter new Channel {1-14}:”. Then, pre

3 2. Installation ① Choose the place with the consideration of power outlet and network connection (RJ-45 Cable connection) to install the Access

66⑥ Select the following order to set Subnet Mask. Enter the proper subnet mask after the phrase “Enter new Subnet Mask :”. Then, press [ENTER

67⑨ If you want to change Password, select the following order on [ROOT] menu. Select [Administration] menu on [Advanced] Menu. Select “Change p

68 Enter the current password (Max. 30 characters) after “Enter current password (Max. 30 characters):”. Then, press [ENTER : ↵]. Enter the new pass

69⑩ You must select “Save and reboot” on [ROOT] menu, after changing the appropriate parameters by entering the new values. By selecting the above

70⑪ After following all the steps mentioned above, you can close the HyperTerminal window if there is no need for change or setting. Select [Basic] m

7119. Load default values Using RS-232C(COM Port) ⑫ Select “Load default values” on [ROOT] menu ⑬ If you want to set default values, enter “y(

7220. Firmware Upgrade Using RS-232C(COM Port) ① Click the “Hyperterminal icon” saved in hard disk of your PC’ ② “Enter password” menu will be

73 ⑥ If you want to upgrade the AP firmware, enter “y(yes)” after “Do you really want to upgrade the firmware via serial ?” then, press [Enter:↵]. E

74⑧ Select [transfer] menu on “Menu Bar” then, select “Send File“. ⑨ Click [Browse] button on the “Send File” window ⑩ After select the firm

75⑪ “1K Xmodem” should be selected on Protocol, then click [send] button. The following window shows the status of loading the AP firmware ima

4 ⑧ Insert Wireless LAN Card into your PC. Wireless LAN Cards are available both for desktop and notebook PCs. PCI Wireless LAN Card is used for

76APPENDIX ⅠⅠⅠⅠ. Explanation of Basic Configuration to use AP Manager # Explanation of AP External Icons DC 5V Power LED(Green), it is always o

77 The window above shows “AP Manager” window. You can select menu from this “Menu Bar”. You can select each function of AP setting tabs on thi

78 “List Box” shows Access Points connected to same network segment, and “Selected AP’s Info” shows simple information of selected AP. “Dialogue

79 This “Button Bar” consists of buttons showing AP Scan, Entering setting values, AP information and AP Manager information. This is “AP Monitor

80 The window above shows “Configuration Summary”, and it appears when you select [Confirm & Apply] button. This is “Password Window” for u

81APPENDIX ⅡⅡⅡⅡ. Specification GeneralWireless NetworkArchitectureIEEE 802.11b(DSSS)Wired Network Architecture Ethernet (10/100Mbps)Power Adapter 9

82Management FeaturesLocal Configuration Serial EIA-232Remote Configuration- HTTP, Telnet, SNMP supported- AP Manager for Microsoft Windows 95/98/200

83Environmental InformationOperating Temperature 0℃℃℃℃ to 45 ℃℃℃℃(32℉℉℉℉ to 113 ℉℉℉℉)Storage Temperature -25℃℃℃℃to 70℃℃℃℃(-13℉℉℉℉to 158℉℉℉℉)Humidity

We value your feedback. If you find errors or omissions in this manuscript, or if you can suggest ways to improve its usefulne

53333. AP Basic Setting Using AP Manager ① Execute AP Manager(SWL-3000AP Series, 4000AP Series Management Utility) under MS-Windows 95/98/Me/2000/NT