Samsung 270A - SRP Two-color Dot-matrix Printer Instrukcja Operatora Strona 1

Operator’s Manual All specifications are subjected to change without notice SRP-270 SERIES 1 STATION PRINTER

104). Put the roll paper on the paper holder and insert the paper in the printer. " SRP-270 A/C : 1Ply Paper

115) Insert the end of the roll paper straight into the paper inlet. The printer feeds the paper automatically an

127). Insert the end of the roll paper into the groove on the Roller-Pulley, warp the paper around it two or thr

13Chapter 4. Setting the DIP switches The DIP switches are located on the bottom of the printer. The DIP switches ar

14 Serial Interface (RS-232C/RS-485) Specification DIP Switch 1 Setting Emulation mode selection Dip Switch

15 Parallel/USB Interface Specification DIP Switch 1 Setting Emulation mode selection Dip Switch 2 Setting S

16Chapter 5. Hexadecimal Dumping This feature allows experienced users to see exactly what data is coming to the pri

17Chapter 6. The self test The self-test checks whether the printer has any problems. If the printer does not functi

18Chapter 7. Code Table The following pages show the character code tables. To find the character corresponding to a

19 Page 2 ( PC850 : Multilingual )

2Warning - U.S. This equipment has been tested and found to comply with the limits for a Class A digital device pursu

20 Page 3 ( PC860 : Portuguese )

21 Page 4 ( PC 863 : Canadian - French )

22 Page 5 ( PC 865 : Nordic )

23 Page 19 ( PC 858 : Euro )

24 International Character

25Chapter 8. Control Commands List EPSON mode Control code Hexadecimal code Function <HT> 09 Horizontal tab

26Control code Hexadecimal code Function <ESC> r n 1B 72 n Select print color <ESC> m 1B 6D Execute

27 STAR mode Control code Hexadecimal code Function <ESC> "C" n 1B 43 n Set page length at n lines

28Control code Hexadecimal code Function <ESC> "z" "1" <ESC> "z" <1>

29Appendix A Connectors

3Table of Contents CHAPTER 1. UNPACKING...4 1-1. CHECKING TH

30Interface Connector Serial Interface(RS-232C) Pin No. Signal name Direction Function 1 FG - Frame Ground 2 T

31Parallel Interface(IEEE-1284) Pin No. Source Compatibility Mode Nibble Mode Byte Mode 1 Host nStrobe HostClk H

32USB Interface Pin No. Signal Name Assignment (Color) Function Shell Shield Drain Wire Frame Ground 1 VBUS

33Appendix B Specification Printing method Serial impact dot matrix Number of head pin 9 wires Printing direction

34Appendix C Removing Jammed Paper 1) Open the printer cover 2) Raise the auto cutter unit by lifting the knob lock.

356) Move the print head carriage to the reverse direction of paper jam. By pushing on the side of the print head as

36 NOTE : If you are troubled with reloading the paper, the cutter blade may not be in its normal position. Insert a screw

4Chapter 1. Unpacking 1-1. Checking the Contents of the printer box After unpacking the unit, check that all the

5 1-3. Functions l The power switch is used to turn the printer on and off. l The FEED button is used to feed roll p

6Chapter 2. Connecting the cables 2-1. Connecting the AC adapter to the printer 1). Make sure that

72-2. Connecting Interface Cable and Drawer Cable to the printer Connect the Host Computer(POS/ECR) to t

8Chapter 3. Installing the roll paper 3-1. Ribbon Cassette Installation 1). Before inserting the ribbon cassette,

93-2. Roll Paper Installation Be sure to use roll paper that matches the printer's specifications. 1). Whe