Samsung 78DF Instrukcja Konfiguracji

Install drivers SAMTRON 591S/58V/59E/78E/78DF/78BDF/98PDF

(The configuration at the back of the monitor may vary from product to product.) Power port Connect the power cord for your monitor to the powe

Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor

Stand Stand For Multimedia model (Option) Manual User Guide CableSound Cables(2each) DC Power Cord Stand Multimedia Speaker S

Menu button [ ] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. Adjust buttons [ ] These buttons allow you

Signal CableConnect the signal cable to the video port on your computer, video board, video card, or graphics card.See Connecting the Monitor for

Setup-For Multimedia model | Multimedia Speaker Stand 1.Connect the power cord for your monitor to the power port on the back of the monitor. Plu

1.Turn off your computer and unplug the power cord. 2.Connect the end of the signal cable to your computer's video port(video board, video card o

5. On/Off Volume Turns On/Off and adjusts the output volume. 6. Treble Control Use to control high frequencies. 7. Bass Control Use to control low

Remove the twist-tie before attaching the base to the monitor. Attaching the Base1. Place the monitor upside-down on a flat work surface. 2. Align th

1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the &qu

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and under

3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Propertie

7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next"

10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Fou

9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your mon

Setup-For Multimedia model | Multimedia Speaker Stand 1.Connect the power cord for your monitor to the power port on the back of the monitor. Plu

1.Turn off your computer and unplug the power cord. 2.Connect the end of the signal cable to your computer's video port(video board, video card o

5. On/Off Volume Turns On/Off and adjusts the output volume. 6. Treble Control Use to control high frequencies. 7. Bass Control Use to control low

Remove the twist-tie before attaching the base to the monitor. Attaching the Base1. Place the monitor upside-down on a flat work surface. 2. Align th

1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the &qu

3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the "Propertie

z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric sho

7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next"

10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Fou

9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your mon

1.Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. 2.These buttons allow you to highlight and adjust items in the m

Contrast

OSD Description Play/stopAdjust the Brightness.Adjust the Contrast.A "Moiré" pattern can appear on your screen, looking like a series of con

Color temperature is a measure of the 'warmth' of the image colors. (6500K / 9300K)Use to adjust the monitor color setting.(Red)Use to adjus

You can see the frequency (user control mode) used by the user, the polarity of the operational signals, the default frequency (default mode) set when

1.Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. 2.These buttons allow you to highlight and adjust items in the m

Contrast

Do not drop the monitor when moving it. z This may cause damage to the product or human body. Place the monitor on a flat and stable surface. zTh

OSD Description Play/stopAdjust the Brightness.Adjust the Contrast.A "Moiré" pattern can appear on your screen, looking like a series of con

Color temperature is a measure of the 'warmth' of the image colors. (6500K / 9300K)Use to adjust the monitor color setting.(Red)Use to adjus

You can see the frequency (user control mode) used by the user, the polarity of the operational signals, the default frequency (default mode) set when

1.Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. 2.These buttons allow you to highlight and adjust items in the m

Contrast

OSD Description Play/stopAdjust the Brightness.Adjust the Contrast.A "Moiré" pattern can appear on your screen, looking like a series of con

Color temperature is a measure of the 'warmth' of the image colors. The available range is between 5000 to 9300K.Use to adjust the monitor c

You can see the frequency (user control mode) used by the user, the polarity of the operational signals, the default frequency (default mode) set w

Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please

speaker or a high voltage wire near by?Is the voltage stable? The screen image can appear to shake or vibrate at a particular time of day due to low

z You may buy a recommended detergent at any Service Center. If the connector between the plug and the pin is dusty or dirty, clean it properly with

4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have pr

4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after u

General GeneralModel Name SAMTRON 591S/58V/59EPicture TubeType 15"(38cm) DynaFlat (35cm viewable)Deflection angle 90 °Dot Pitch 0.24mm (Horizo

90 ~ 264VAC rms, 60/50 Hz ± 3HzPower ConsumptionLess than 65WDimensions (WxDxH)361 x 379.2 x 347mm (After installation of Stand)Weight11.0kgEnvironmen

Horizontal FrequencyThe time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and

General GeneralModel Name SAMTRON 78EPicture TubeType 17"(43cm) Full square type (40.6cm viewable)Deflection angle 90 °Dot Pitch 0.23mm (Horiz

Power Supply90 ~ 264VAC rms, 60/50 Hz ± 3HzPower ConsumptionLess than 75WDimensions (WxDxH)401 x 410 x 378mm (After installation of Stand)Weight14.3kg

Display ModeHorizontal Frequency (kHz)Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)VESA, 640 x 480 37.500 75.000 31.500 -/-VESA,

General GeneralModel Name SAMTRON 78DFPicture TubeType 17"(43cm) DynaFlat (40.6cm viewable)Deflection angle 90 °Dot Pitch 0.20mm (Horizontal)S

Power Supply90 ~ 264VAC rms, 60/50 Hz ± 3HzPower ConsumptionLess than 75WDimensions (WxDxH)401 x 410 x 378mm (After installation of Stand)Weight14.3kg

Do not use or store inflammable substances near the monitor. z This may cause an explosion or fire. Do not try to move the monitor by pulling only t

Display ModeHorizontal Frequency (kHz)Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)VESA, 640 x 480 37.500 75.000 31.500 -/-VESA,

General GeneralModel Name SAMTRON 78BDFPicture TubeType 17"(43cm) DynaFlat (40.6cm viewable)Deflection angle 90 °Dot Pitch 0.20mm (Horizontal)

90 ~ 264VAC rms, 60/50 Hz ± 3HzPower ConsumptionLess than 75WDimensions (WxDxH)401 x 410 x 378mm (After installation of Stand)Weight14.3kgEnvironmenta

Display ModeHorizontal Frequency (kHz)Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)VESA, 640 x 480 37.500 75.000 31.500 -/-VESA, 1

General GeneralModel Name SAMTRON 98PDFPicture TubeType 19"(48cm) DynaFlat (45.8cm viewable)Deflection angle 90 °Dot Pitch 0.20mm (Horizontal)

90 ~ 264VAC rms, 60/50 Hz ± 3HzPower ConsumptionLess than 110 WDimensions (WxDxH)445 x 457.5 x 416mm (After installation of Stand)Weight18.2kgEnvironm

Display ModeHorizontal Frequency (kHz)Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)VESA, 640 x 480 37.500 75.000 31.500 -/-VESA, 1

Service The address and phone number of the company can be changed without previous notice. SAMTRON CANADASAMSUNG ELECTRONICS CANADA INC. 7037 F

17TH, HAMACHO CENTER BLDG. 2-31-1, NIHONBASHI-HAMACHO, CHOU-KU, TOKYO 103, JAPAN TEL : (81-3) 5641-9860 FAX : (81-3) 5641-9861SAMTRON U.S.A.SAMTRON CO

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trad

Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor

FCC Information | IC Compliance Notice | MPR II Compliance | European Notice (Europe only) | PCT Notice | VCCI | TCO'95-Ecological requirements f

MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice(Europe Only)

the adaptation of goods and services to the environment.The main problem as far as monitors and other electronic equipment are concerned is that envir

Mercury Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses. z TCO'95 req

complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): devel

Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured an

Stand Stand For Multimedia model (Option) Manual User Guide CableSound Cables(2each) DC Power Cord Stand Multimedia Speaker S

Menu button [ ] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. Adjust buttons [ ] These buttons allow you